碳纳米管增强铜铬基复合材料的制备及其性能研究

doi:10.3969/j.issn.2095-2198.2023.03.001

摘要
参考文献
相关文章
推荐阅读
Metrics

下载:

PDF (1557KB)
输出: BibTeX | EndNote (RIS)

摘要

以带羧基官能团的碳纳米管和片状铜铬粉为原料，通过对片状铜铬粉表面进行亲水处理，并采用湿法分散—粉末冶金工艺制备得到了碳纳米管/铜铬复合材料，实现了碳纳米管在铜铬基体中的均匀分散.采用场发射扫描电镜观察了复合材料块体的组织形貌，并研究了碳纳米管和铬含量对复合材料力学性能和导电性能的影响.结果表明：碳纳米管的体积分数为2%，铬在合金粉中的质量分数为3%为最优体系；碳纳米管的加入使铜铬基体的屈服强度提高了约12%，抗拉强度提高了约13%，摩擦系数降低了约19%，导电率降低了约23%.

	服务
	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	（）
	作者相关文章

关键词: 铜铬基复合材料')" href="#">

铜铬基复合材料碳纳米管力学性能电导率

Abstract:

Carbon nanotube (CNT) with carboxyl functional groups and flake Cu-Cr powder were used as raw materials.The surface of flake Cu-Cr powder was treated by hydrophilic functional groups,and the CNT/Cu-Cr matrix composites were prepared by wet dispersion and powder metallurgy process,realizing the uniform dispersion of carbon nanotube in the Cu-Cr matrix.The microstructure of the composite block was observed by field emission scanning electron microscope,and the effects of CNT and Cr content on the mechanical and electrical properties of the composites were studied.The results showed that the optimal system was the composites containing CNT with a volume fraction of 2% and Cr with a mass fraction of 3% in the alloy powder (2% CNT/Cu-3Cr).In comparison with the Cu-3Cr bulk,the yield strength increased by about 12%,the tensile strength increased by about 13%,the friction coefficient decreased by about 19% and the electrical conductivity decreased by about 23%.

Key words: Cu-Cr matrix composite')" href="#">

Cu-Cr matrix composite carbon nanotube mechanical property electrical conductivity

出版日期: 2023-06-30 发布日期: 2024-03-06 整期出版日期: 2023-06-30

ZTFLH:

TB333

基金资助:

国家自然科学基金项目(21502118)；辽宁省自然基金项目(2019-ZD-0071)

通讯作者: 李文泽

作者简介: 朱晓宇（1985—），女，湖北襄阳人，副教授，博士，主要从事有机合成与催化研究.

引用本文:

朱晓宇1, 梁雨苏2, 李文泽1.

碳纳米管增强铜铬基复合材料的制备及其性能研究 [J]. 沈阳化工大学学报, 2023, 37(3): 193-199.
ZHU Xiaoyu 1, LIANG Yusu 2, LI Wenze 1.

Preparation and Properties of Carbon Nanotube Reinforced Cu-Cr Matrix Composite . Journal of Shenyang University of Chemical Technology, 2023, 37(3): 193-199.

链接本文:

https://xuebao.syuct.edu.cn/CN/10.3969/j.issn.2095-2198.2023.03.001 或 https://xuebao.syuct.edu.cn/CN/Y2023/V37/I3/193

［1］BIRCH E M,RUDA-EBERENZ T A,CHAI M,et al.Properties that Influence the Specific Surface Areas of Carbon Nanotubes and Nanofiber［J］.Annals of Occupational Hygiene,2013,57(9):1148-1166.

［2］张辉,孙伟,杨鹏.碳纳米管导电增强聚乙撑二氧噻吩复合材料的研究［J］.沈阳化工大学学报,2013,27(4):320-326.

［3］葛铁军,汪晶.碳纳米管耐磨改性MC尼龙及磨损机理［J］.沈阳化工大学学报,2014,28(1):37-41.

［4］XU C L,WEI B Q,MA R Z,et al.Fabrication of Aluminum-Carbon Nanotube Composites and Their Electrical Properties［J］.Carbon,1999,37(5):855-858.

［5］LI C D,WANG X J,LIU W Q,et al.Microstructure and Strengthening Mechanism of Carbon Nanotubes Reinforced Magnesium Matrix Composite［J］.Materials Science and Engineering A,2014,597:264-269.

［6］ZARE H,JAHEDI M,TOROGHINEJAD M R,et al.Compressive,Shear,and Fracture Behavior of CNT Reinforced Al Matrix Composites Manufactured by Severe Plastic Deformation［J］.Materials & Design,2016,106:112-119.

［7］ZHAO S,ZHENG Z,HUANG Z X,et al.Cu Matrix Composites Reinforced with Aligned Carbon Nanotubes:Mechanical,Electrical and Thermal Properties［J］.Materials Science and Engineering:A,2016,675:82-91.

［8］易健宏,杨平,沈韬.碳纳米管增强金属基复合材料电学性能研究进展［J］.复合材料学报,2016,33(4):689-703.

［9］ZHANG X X,ZHANG J F,LIU Z Y,et al.Microscopic Stresses in Carbon Nanotube Reinforced Aluminum Matrix Composites Determined by In-Situ Neutron Diffraction［J］.Journal of Materials Science & Technology,2020,54:58-68.

［10］陈文亮,黄春平,柯黎明.碳纳米管增强铜基复合材料的研究进展［J］.机械工程材料,2012,36(6):5-8,12.

［11］CHA S I,KIM K T,ARSHAD S N,et al.Extraordinary Strengthening Effect of Carbon Nanotubes in Metal-Matrix Nanocomposites Processed by Molecular-Level Mixing［J］.Advanced Materials,2005,17(11):1377-1381.

［12］KIM K T,CHA S I,HONG S H,et al.Microstructures and Tensile Behavior of Carbon Nanotube Reinforced Cu Matrix Nanocomposites［J］.Materials Science and Engineering A,2006,430(1/2):27-33.

［13］LIM B,KIM C J,KIM B,et al.The Effects of Interfacial Bonding on Mechanical Properties of Single-Walled Carbon Nanotube Reinforced Copper Matrix Nanocomposites［J］.Nanotechnology,2006,17(23):5759-5764.

［14］KIM K T,CHA S I,HONG S H.Hardness and Wear Resistance of Carbon Nanotube Reinforced Cu Matrix Nanocomposites［J］.Materials Science and Engineering A,2007,449/451:46-50.

［15］陶静梅,洪鹏,陈小丰,等.碳纳米管增强铜基复合材料的研究进展［J］.材料工程,2017,45(4):128-136.

［16］王英文,王开,于欣瑞,等.碳纳米管对CuO-ZnO-Ga₂O₃/HZSM-5催化剂性能的影响［J］.沈阳化工大学学报,2020,34(3):210-215.

［17］DONG S R,TU J P,ZHANG X B.An Investigation of the Sliding Wear Behavior of Cu-Matrix Composite Reinforced by Carbon Nanotubes［J］.Materials Science and Engineering A,2001,313(1/2):83-87.

［18］CHEN W X,TU J P,WANG L Y,et al.Tribological Application of Carbon Nanotubes in a Metal-Based Composite Coating and Composites［J］.Carbon,2003,41(2):215-222.

［19］CHEN X H,LI W H,CHEN C S,et al.Preparation and Properties of Cu Matrix Composite Reinforced by Carbon Nanotubes［J］.Transactions of Nonferrous Metals Society of China,2005,15(2):314-318.

［20］蒋太炜,蔡晓兰,王开军,等.高能球磨法制备CNTs增强铜基复合材料粉末［J］.科学技术与工程,2012,12(17):4271-4273.

［21］周志明,王亚平,夏华,等.Cu-Cr合金制备技术的研究进展［J］.材料导报,2008,22(3):44-47.

［22］孟振强,熊拥军,刘如铁,等.Ni-P-多壁碳纳米管复合镀层的制备及自润滑机理［J］.中南大学学报(自然科学版),2012,43(9):3394-3400.

[1]	马亚辉, 王建, 牛永安. 金刚烷型双马来酰亚胺树脂共聚体系的固化成型与性能研究 [J]. 沈阳化工大学学报, 2023, 37(1): 37-43.

No Suggested Reading articles found!

Viewed

Full text

Abstract

Cited

Shared

Discussed